DA-CG

DA-CG

In-Line Detonation Flame Arrester

for unstable and stable detonations and deflagrations in a straight through design with shock absorber, bidirectional

Функция и описание

The PROTEGO® DA-CG series of detonation arresters was mainly developed for the North American market and optimized to meet the demands of the US Coast Guard. The devices are symmetrical and offer bidirectional flame arresting for deflagrations, stable and unstable detonations.

The speed of incoming detonations is greatly reduced by the effective shock absorber (1). This improves the flame extinction in the narrow gaps of the FLAMEFILTER® (3).

The flame arrester essentially consists of two housing parts with an integrated shock absorber and the PROTEGO® flame arrester unit (2) in the center. The PROTEGO® flame arrester unit is modular and consists of several FLAMEFILTER® discs and spacers firmly held in a FLAMEFILTER® cage. The number of FLAMEFILTER® discs and their gap size depends on the arrester‘ s conditions of use.

By indicating the operating parameters such as the temperature, pressure and explosion group and the composition of the fluid, the optimum in-line detonation flame arrester can be selected. Type PROTEGO® DA-CG flame arresters are available for explosion groups IIA to IIB3 (NEC group D to C MESG ≥ 0.65 mm).

The standard design can be used up to an operating temperature of +60°C / 140°F and an absolute operating pressure acc. to table 3. Devices with special approvals can be obtained for higher pressures and higher temperatures upon request.

The flame arresters have been approved according to the American Standard 33 CFR part 154 and are accepted by the US Coast Guard.

Особые признаки и преимущества

  • offers protection against deflagrations, stable and unstable detonations
  • less number of FLAMEFILTER® discs from the use of the effective shock absorber
  • modular flame arrester unit enables each individual FLAMEFILTER® discs to be replaced and cleaned
  • different series allow increase of FLAMEFILTER ® size for given flange connection resulting in lower pressure drop across the device
  • service-friendly design
  • also available for large nominal sizes
  • expanded application range for higher operating temperatures and pressures
  • bidirectional operation as well as any direction of flow and installation position
  • Possible installation of temperature sensors
  • minimum pressure loss and associated low operating and life-cycle cost
  • cost efficient spare parts

Таблица параметров

To select nominal width/nominal size (NG/DN) - combination, please use the flow capacity charts on the following pages. Additional nominal width/nominal size (NG/DN) - combinations for improved flow capacity upon request.

NG150 / 6"150 / 6"200 / 8"300 / 12"400 / 16"500 / 20"600 / 24700 / 28"800 / 32"1000 / 40"1200 / 48"
DN≤ 50 / 2"65, 80 / 2 ½“, 3≤ 100 / 4"≤ 150 / 6"≤ 200 / 8"≤ 250 / 10"≤ 300 / 12"≤ 350 / 14"≤ 400 / 16"≤ 500 / 20"≤ 600 / 24"
a285 / 11.22285 / 11.22340 / 13.39460 / 11.18580 / 22.83715 / 28.15840 / 33.071025 / 40.351025 / 40.351255 / 49.411485 / 58.46
b650 / 25.59650 / 25.59700 / 27.56800 / 31.50900 / 35.431100 / 43.311250 / 49.211500 / 59.061500 / 59.061700 / 66.932000 / 78.74
c300 / 11.81300 / 11.81330 / 12.99380 / 14.96490 / 19.29540 / 21.26590 / 23.23690 / 27.17690 / 27.17790 / 31.10880 / 34.65
NG150 / 6"150 / 6"200 / 8"300 / 12"400 / 16"500 / 20"600 / 24700 / 28"800 / 32"1000 / 40"1200 / 48"
DN≤ 50 / 2"65, 80 / 2 ½“, 3≤ 100 / 4"≤ 150 / 6"≤ 200 / 8"≤ 250 / 10"≤ 300 / 12"≤ 350 / 14"≤ 400 / 16"≤ 500 / 20"≤ 600 / 24"
a285 / 11.22285 / 11.22340 / 13.39460 / 11.18580 / 22.83715 / 28.15840 / 33.071025 / 40.351025 / 40.351255 / 49.411485 / 58.46
b650 / 25.59650 / 25.59700 / 27.56800 / 31.50900 / 35.431100 / 43.311250 / 49.211500 / 59.061500 / 59.061700 / 66.932000 / 78.74
c300 / 11.81300 / 11.81330 / 12.99380 / 14.96490 / 19.29540 / 21.26590 / 23.23690 / 27.17690 / 27.17790 / 31.10880 / 34.65

размер в мм

DA-CG

Выбор материала корпуса

Design AB
HousingSteelStainless Steel
GasketPTFEPTFE
Flame arrester unitAB
Design AB
HousingSteelStainless Steel
GasketPTFEPTFE
Flame arrester unitAB

Special materials upon request

Комбинация материалов элемента огнепреградителя

Design AB
FLAMEFILTER® cageSteelStainless Steel
FLAMEFILTER®*Stainless SteelStainless Steel
SpacerStainless SteelStainless Steel
Design AB
FLAMEFILTER® cageSteelStainless Steel
FLAMEFILTER®*Stainless SteelStainless Steel
SpacerStainless SteelStainless Steel

*the FLAMEFILTER® are also available in the materials Tantalum, Inconel, Copper, etc. when the listed housing and cage materials are used.

Special materials upon request

DA-CG

Выбор группы взрывоопасности

MESGExpl. Gr. (IEC / CEN)Gas Group (NEC)
> 0,90 mmIIAD
≥ 0,65 mmIIB3C
MESGExpl. Gr. (IEC / CEN)Gas Group (NEC)
> 0,90 mmIIAD
≥ 0,65 mmIIB3C

Special approvals upon request

Выбор максимального рабочего давления P

Expl. Gr.DN50 / 2"80 / 3"100 / 4"150 / 6"200 / 8"250 / 10"300 / 12"350 / 14"400 / 16"500 / 20"600 / 24"
NG150 / 6''150 / 6''200 / 8''300 / 12''400 / 16''500 / 20''600 / 24''700 / 28''800 / 32''1000 / 40''1200 / 48''
IIA (D)Pmax1,2 / 17.41,2 / 17.41,2 / 17.41,2 / 17.41,2 / 17.41,2 / 17.41,2 / 17.41,2 / 17.41,2 / 17.41,2 / 17.41,2 / 17.4
IIB3 (C)Pmax1,6 / 23.21,6 / 23.21,6 / 23.21,6 / 23.21,6 / 23.21,6 / 23.21,6 / 23.21,6 / 23.21,6 / 23.21,6 / 23.21,6 / 23.2
Expl. Gr.DN50 / 2"80 / 3"100 / 4"150 / 6"200 / 8"250 / 10"300 / 12"350 / 14"400 / 16"500 / 20"600 / 24"
NG150 / 6''150 / 6''200 / 8''300 / 12''400 / 16''500 / 20''600 / 24''700 / 28''800 / 32''1000 / 40''1200 / 48''
IIA (D)Pmax1,2 / 17.41,2 / 17.41,2 / 17.41,2 / 17.41,2 / 17.41,2 / 17.41,2 / 17.41,2 / 17.41,2 / 17.41,2 / 17.41,2 / 17.4
IIB3 (C)Pmax1,6 / 23.21,6 / 23.21,6 / 23.21,6 / 23.21,6 / 23.21,6 / 23.21,6 / 23.21,6 / 23.21,6 / 23.21,6 / 23.21,6 / 23.2

Pmax = maximum allowable operating pressure in bar / psi absolute, higher operating pressure upon request

Спецификация макс. рабочей температуры

≤ 60°C / 140°FTmaximum allowable operating temperature in °C
-Designation
≤ 60°C / 140°FTmaximum allowable operating temperature in °C
-Designation

higher operating temperatures upon request

Вид фланцевого соединения

EN 1092-1; Form B1
ASME B16.5; 150 lbs RFSF
EN 1092-1; Form B1
ASME B16.5; 150 lbs RFSF

other connections upon request

Модели и спецификация

There are three different designs available:

Basic design of the detonation arrester

DA-CG- –

In-line detonation flame arrester with integrated temperature sensor* as additional protection against short time burning of one side

DA-CG- T

Detonation arrester with two integrated temperature sensors* as additional protection against short time burning from both sides

DA-CG- TB

Basic design of the detonation arrester

DA-CG- –

In-line detonation flame arrester with integrated temperature sensor* as additional protection against short time burning of one side

DA-CG- T

Detonation arrester with two integrated temperature sensors* as additional protection against short time burning from both sides

DA-CG- TB

Additional special arresters upon request
*Resistance thermometer for device group II, category (1) 2 (GII cat. (1) 2)

DA-CG

Диаграммы пропускной способности

Диаграммы пропускной способности были определены с помощью калибрированной и сертифицированной объединением технического надзора (TÜV) проточной измерительной установки. Пропускная способность V. в м³/час определена воздухом при нормальных атмосферных условиях в соответствии с ISO 6358 (20°C, 1 бар). Преобразование для различных плотностей и температур см. главу 1: Технические основы

DA-CG
DA-CG