BE/HR-E-IIB3

BE/HR-E-IIB3

Deflagration Flame Arrester, endurance burning proof, End-of-Line

Функция и описание

The PROTEGO® BE/HR-E-IIB3 end-of-line deflagration flame arrester was specifically developed for vessels which are not pressurized and store Ethanol or other alcohols. The combustion of alcohol requires a modified flame arrester element design to provide protection against endurance burning. In addition, the device provides protection against atmospheric deflagration.Main application area is on suction and vent lines, for sea going vessels but also useful for inland navigation vessels with the goal to prevent flame transmission caused by endurance burning or atmospheric deflagration.

The PROTEGO® BE/HR-E-IIB3 consists of a housing (1), a weather hood (2) and the PROTEGO® flame arrester unit (3). During normal operation, the metal weather hood is in a closed position. If a flame burns on the flame arrester element surface, the fusible link (5), located in a center position, will melt and let the spring loaded weather hood move into the open position. The PROTEGO® flame arrester unit consists of two FLAMEFILTER® discs (4), which are installed in a FLAMEFILTER® cage. The PROTEGO® BE/HR-E end-of-line deflagration flame arrester is available for hydrocarbons for explosion group IIB3 (MESG ≥ 0,65 mm) and alcohols.

The standard design can be used for operating temperatures up to +60°C / 140°F.

Type-approved in accordance with ATEX Directive and EN ISO 16852 as well as other international standards. Approved according to IMO MSC/Circular 677 and 1009 as well as IMO MSC.1/Circular 1324 and 1325.

Особые признаки и преимущества

  • endurance burning protection for alcohols and hydrocarbons up to explosion group IIB3
  • specially developed for sea going vessels but also useful for inland navigation vessels and on shore systems
  • weather hood protects against environmental Impact (i.e. weather, bird nests, etc.)
  • weather hood opens and signals the impact of a flame
  • fusible link is resistant against chemicals
  • modular design allows replacement of single FLAMEFILTER®
  • protection against atmospheric deflagration and endurance burning
  • modular design results in low spare part cost

Таблица параметров

To select the nominal size (DN), please use the flow capacity charts on the following pages

DN80 / 3"100 / 4"
a353 / 13.90353 / 13.90
b250 / 9.84250 / 9.84
DN80 / 3"100 / 4"
a353 / 13.90353 / 13.90
b250 / 9.84250 / 9.84

размер в мм Dimensions for Deflagration flame arrester with heating jacket upon request

BE/HR-E-IIB3

Выбор материала корпуса

Design BC
HousingSteelStainless Steel
Weather HoodSteelStainless Steel
Flame arrester unitAA, C
Design BC
HousingSteelStainless Steel
Weather HoodSteelStainless Steel
Flame arrester unitAA, C

Special materials upon request

Комбинация материалов элемента огнепреградителя

DesignAC
FLAMEFILTER® cageStainless SteelStainless Steel
FLAMEFILTER®Stainless SteelHastelloy
SpacerStainless SteelHatelloy
DesignAC
FLAMEFILTER® cageStainless SteelStainless Steel
FLAMEFILTER®Stainless SteelHastelloy
SpacerStainless SteelHatelloy

Special materials upon request

BE/HR-E-IIB3

Выбор группы взрывоопасности

MESGExpl. Gr. (IEC / CEN)Gas Group (NEC)
≥ 0,65 mmIIB3C
MESGExpl. Gr. (IEC / CEN)Gas Group (NEC)
≥ 0,65 mmIIB3C

Special approvals upon request

Вид фланцевого соединения

EN 1092-1; Form B1
ASME B16.5; 150 lbs RFSF
EN 1092-1; Form B1
ASME B16.5; 150 lbs RFSF

other connections upon request

Модели и спецификация

В наличии имеются две модели:
Вентиляционный колпак в обычном исполнении

BE/HR-E - –

Вентиляционный колпак с рубашкой обогрева

BE/HR-E - H

Вентиляционный колпак в обычном исполнении

BE/HR-E - –

Вентиляционный колпак с рубашкой обогрева

BE/HR-E - H

Специальная арматура по заказу клиента
BE/HR-E-IIB3

Диаграммы пропускной способности

Диаграммы пропускной способности были определены с помощью калибрированной и сертифицированной объединением технического надзора (TÜV) проточной измерительной установки. Пропускная способность V. в м³/час определена воздухом при нормальных атмосферных условиях в соответствии с ISO 6358 (20°C, 1 бар). Преобразование для различных плотностей и температур см. главу 1: Технические основы

BE/HR-E-IIB3
BE/HR-E-IIB3