Skip to main content

V/KSM

Vacuum Relief Valve made of plastic

  • 10% technology for minimum pressure increase up to full lift
  • extreme tightness, resulting in lowest possible product losses and reduced environmental pollution
  • set pressure close to opening pressure for optimum pressure maintenance in the system
  • valve pallet is guided inside the housing to protect against harsh weather conditions
  • non-corrosive
  • especially suitable for aggressive, sticky, or polymerizing substances
  • weight reduction in comparison to steel/stainless steel
  • high surface quality
  • automatic condensate drain
  • different plastics can easily be combined
  • maintenance-friendly design

Функция и описание

The PROTEGO® valve V/KSM is a state-of-the-art vacuum relief valve with excellent flow performance made of high-grade synthetic material. It is used as a device to relieve vacuum in tanks, containers, and process engineering equipment. It prevents the in-breathing of air until reaching the set pressure. The valve is a perfect solution for corrosive, polymerizing, or sticky substances.

The device will start to open as soon as the set pressure is reached and is fully open within 10% pressure increase. Continuous investments in and a commitment to research and development have allowed PROTEGO® to develop a low pressure valve which has the same opening characteristic as a high pressure safety relief valve. This “full lift type” technology allows the valve to be set at just 10% below the maximum allowable working vacuum (MAWV) of the tank and still safely vent the required mass flow.

Due to our highly developed manufacturing technology, the tank pressure is maintained up to the set pressure with a seal that is far superior to the conventional standard. This feature is achieved by valve seats made of high-performance plastics and a high grade PTFE seal. After the vacuum is released, the valve re-seats and provides a tight seal.

The optimized fluid dynamic design of the valve body and valve pallet is a result of many years of research, resulting in a stable operation of the valve pallet, optimized performance, and reduced product losses.

Таблица параметров

To select the nominal size (DN), use the flow capacity chart on the following page

DN50 / 2" 80 / 3" 100 / 4"150 / 6" 200 / 8"
a57 / 2.2477 / 3.0387 / 3.43126 / 4.96180 / 7.09
a(115 / 4.53)*(146 / 5.75)*(175 / 6.89)*
b259 / 10.20376 / 14.80373 / 14.69460 / 18.11469 / 18.46
b(338 / 13.31)*(427 / 16.81)*(437 / 17.20)*
c150 / 5.91200 / 7.87225 / 8.86280 / 11.02350 / 13.78
d180 / 7.09250 / 9.84300 / 11.81350 / 13.78560 / 22.05
d(405 / 15.94)*(500 / 19.68)*
размер в мм * Dimensions in brackets only for PVDF

Выбор материала корпуса

Design A B C
HousingPEPPPVDF
Valve seatPEPPPVDF
SealingFPMFPMFPM
Valve palletA, C, DB, C, DC, D
Special materials upon request

Material selection for vacuum valve pallet

Design A B C D
Pressure range [mbar]
[inch W.C.]
+6,0 up to +16
+2.4 up to +6.4
+5,5 up to +16
+2.2 up to +6.4
+9,5 up to +30
+3.8 up to +12
+30 up to +100
+12 up to +40
Valve palletPEPPPVDFHastelloy
SealingPTFEPTFEPTFEPTFE
Spindle guidePEPPPVDFHastelloy
WeightPEPPPVDFHastelloy
Special materials and other pressure Settings upon request

Вид фланцевого соединения

 EN 1092-1, Форма B1
ASME B16.5 CL 150 F.F.
other types upon request

Модели и спецификация

The valve pallet is weight-loaded, and the highest pressure levels are only attained with metal discs.

Vacuum valve in basic design

Additional special devices available upon request.

Settings

Vacuum:

-6.0 mbar -100 mbar (DN 50/2”)
-2.4 inch W.C. -40 inch W.C.
-4.0 mbar -100 mbar (DN 80/3”)
-1.6 inch W.C. -40 inch W.C.
-4.5 mbar -100 mbar (DN 100/4” - DN 200/8”)
-1.8 inch W.C. -40 inch W.C.
Higher pressure settings upon request.

Диаграммы пропускной способности

Диаграммы пропускной способности были определены с помощью калибрированной и сертифицированной объединением технического надзора (TÜV) проточной измерительной установки. Пропускная способность V. в м³/час определена воздухом при нормальных атмосферных условиях в соответствии с ISO 6358 (20°C, 1 бар). Преобразование для различных плотностей и температур см. главу 1: Технические основы