SD/BS-H

SD/BS-H

Pressure Relief Valve

in heat jacketed design

Function and Description

The SD/BS-H type PROTEGO® valve is a highly developed pressure relief valve with a heating jacket down to the flange. It is primarily used as pressure relief device for vessels and process engineering equipment under difficult operating conditions. This includes extreme weather conditions or products that tend to form polymers at certain temperatures, adhere, or form deposits that negatively influence function (such as bitumen, tar, dust). The valve offers reliable protection against overpressure and prevents the unacceptable loss of product vapors close to the set pressure.

The device will start to open as soon as the set pressure is reached and only requires 10% overpressure to full lift. Continuous investments into research and development have allowed PROTEGO® to develop a low pressure valve which has the same opening characteristic as a high pressure safety relief valve. This “full lift type” technology allows the valve to be set just 10% below the maximum allowable working pressure of the tank and still safely vent the required mass flow.

Due to our highly developed manufacturing technology the tank pressure is maintained up to set pressure, with a tightness that is far superior to the conventional standard. This feature is achieved by valve seats made of high-grade stainless steel with precisely lapped valve pallets and a reinforced housing design. After the excess pressure is discharged, the valve reseats and provides a tight seal again.

Features and Advantages

  • “full lift type” technology valve utilizes only 10% overpressure to reach full lift
  • extreme tightness and hence least possible product losses and reduced environmental pollution
  • set pressure is close to the opening pressure which results in best possible pressure management of the system
  • high flow capacity
  • the valve pallet is guided within the housing to protect against harsh weather conditions
  • can be used in areas subject to an explosion hazard
  • heating jacketed design down to the flange to avoid cold bridges
  • maximum permissible heating medium temperature of 320°C / 608°F (at 6 bar / 87 psi)
  • a special design with a heatable valve cover is available
  • at low pressure settings, an optimized valve pallet cover prevents the set pressure from being distorted by dust or condensate
  • reinforced housing design
  • a special design with a mechanical vent pallet lift device is available

Dimensions

To select the nominal size (DN), use the flow capacity chart on the following page

DN1DN2ab b c d d e
bis 30 mbar> 30 mbarbis 30 mbar> 30 mbar
80 / 3"15 / ½"325 / 12.80400 / 15.75515 / 20.2870 / 2.76250 / 9.84390 / 15.35250 / 9.84
100 / 4"15 / ½"325 / 12.80400 / 15.75505 / 19.8860 / 2.36250 / 9.84380 / 14.96250 / 9.84
150 / 6"15 / ½"405 / 15.94460 / 18.11595 / 23.4360 / 2.36315 / 12.40470 / 18.50290 / 11.42
200 / 8"15 / ½"510 / 20.08470 / 18.50575 / 22.6465 / 2.56305 / 12.01445 / 17.52340 / 13.39
DN1DN2ab b c d d e
bis 30 mbar> 30 mbarbis 30 mbar> 30 mbar
80 / 3"15 / ½"325 / 12.80400 / 15.75515 / 20.2870 / 2.76250 / 9.84390 / 15.35250 / 9.84
100 / 4"15 / ½"325 / 12.80400 / 15.75505 / 19.8860 / 2.36250 / 9.84380 / 14.96250 / 9.84
150 / 6"15 / ½"405 / 15.94460 / 18.11595 / 23.4360 / 2.36315 / 12.40470 / 18.50290 / 11.42
200 / 8"15 / ½"510 / 20.08470 / 18.50575 / 22.6465 / 2.56305 / 12.01445 / 17.52340 / 13.39

Dimensions in mm / inches

* also available with special flange DN 50 / 2''

SD/BS-H

Material selection for housing

Design AB
HousingSteelStainless Steel
Heating JacketSteelStainless Steel
Valve SeatStainless SteelStainless Steel
Design AB
HousingSteelStainless Steel
Heating JacketSteelStainless Steel
Valve SeatStainless SteelStainless Steel

Special materials upon request

Material selection for pressure valve pallet

Design ABC
Pressure range [mbar]
[inch W.C.]
+5,0 up to +25
+2 up to +10
>+10 up to +30
>+4 up to +12
>+30 up to +210
>+12 up to +84
Valve palletAluminiumStainless SteelStainless Steel
Valve pallet hoodStainless SteelStainless Steel-
SealingMetal to MetalMetal to MetalMetal to Metal
Design ABC
Pressure range [mbar]
[inch W.C.]
+5,0 up to +25
+2 up to +10
>+10 up to +30
>+4 up to +12
>+30 up to +210
>+12 up to +84
Valve palletAluminiumStainless SteelStainless Steel
Valve pallet hoodStainless SteelStainless Steel-
SealingMetal to MetalMetal to MetalMetal to Metal

Special materials and devices with higher set pressure or vacuum are available upon request

SD/BS-H

Flange connection type

EN 1092-1; Form B1
ASME B16.5; 150 lbs RFSF
EN 1092-1; Form B1
ASME B16.5; 150 lbs RFSF

other types upon request

Design Types and Specifications

The valve pallet is weight-loaded. Starting at a set pressure of 30 mbar, a vane guide is also used.

Pressure valve in basic design with heating jacket

SD/BS - H

Pressure valve in basic design with heating jacket

SD/BS - H

Additional special devices available upon request.

Settings

Pressure:

+5.0 mbar

+210 mbar

+2.0 inch W.C.

+84 inch W.C.

Higher pressure settings upon request.

SD/BS-H

Flow Capacity Chart

The flow capacity charts have been determined with a calibrated and TÜV certified flow capacity test rig. Volume flow V in (m³/h) and CFH refer to the standard reference conditions of air ISO 6358 (20°C, 1bar). Conversion to other densities and temperatures refer to Vol. 1: “Technical Fundamentals”.

SD/BS-H
SD/BS-H