Skip to main content


Deflagration Flame Arrester, endurance burning proof, End-of-Line

  • weather hood protects against environmental impact (i.e. weather, bird nests, etc.)
  • weather hood will open and signal the impact of a flame
  • endurance burning protection for IIB3 and IIA vapour (NEC group C and D); only for PROTEGO® BE/HK and BE/HK-H
  • fusible link is resistant against chemicals
  • modular design allows replacement of single FLAMEFILTER® discs
  • easy maintenance
  • modular design results in low spare part costs
  • protection against atmospheric deflagration and endurance burning

Функция и описание

For many years the PROTEGO® BE/HK end-of-line deflagration flame arrester has been successfully used to protect vessels and process engineering apparatus which are not pressurized. The device provides protection against flame transmission through atmospheric deflagration and stabilized flames which can burn for very long time on the flame arrester element surface, so called endurance burning. Main application area is on in- and out-breathing and vent lines, with the goal to prevent flame transmission caused by endurance burning or atmospheric deflagration from propagating into the vessel or plant.

The PROTEGO® BE/HK consists of a housing (1), a weather hood (2) and the PROTEGO® flame arrester unit (3). During normal operation the metal weather hood is in a closed position. If a stabilized flame burns on the flame arrester element surface, the fusible link (5), located in a center position, will melt and let the spring loaded weather hood move into the open position. The PROTEGO® flame arrester unit consists of two FLAMEFILTER® discs (4), which are installed in a FLAMEFILTER® casing. The FLAMEFILTER® gap size depends on the devices intended use.

Detailing the operating conditions such as the temperature, explosion group and the composition of the fluid, enables PROTEGO® to select the best end-of-line deflagration flame arrester for your application. The PROTEGO® BE/HK series end-of-line deflagration flame arrester is available for substances from explosion groups IIA to IIB3 (NEC groups D to C MESG ≥ 0.65 mm). In a modified design, this device is also available for Ethanol applications.

The standard design can be used with operating temperature of up to +60°C / 140°F.

Type-approved according to ATEX Directive as well as other international standards.

Таблица параметров

To select the nominal size (DN), please use the flow capacity charts on the following pages

DN 20 / ¾"25 / 1"32 / 1¼"40 / 1½"50 / 2"65 / 2½"80 / 3"
a163 / 6.42163 / 6.42163 / 6.42183 / 7.20183 / 7.20218 / 8.58218 / 8.58
BE / HK-IIAb180 / 7.09177 / 6.97177 / 6.97190 / 7.48190 / 7.48200 / 7.87200 / 7.87
BE / HK-IIB3b180 / 7.09177 / 6.97177 / 6.97----
размер в мм Dimensions for deflagration flame arrester with heating jacket upon request

Выбор материала корпуса

Design BC
HousingSteelStainless Steel
Weather hoodSteelStainless Steel
Flame arrester unitAA, C
Special materials upon request

Комбинация материалов элемента огнепреградителя

Design AC
FLAMEFILTER® cageStainless SteelStainless Steel
FLAMEFILTER®Stainless SteelHastelloy
SpacerStainless SteelHastelloy
Special materials upon request

Выбор группы взрывоопасности

MESGExpl. Gr. (IEC / CEN)Gas Group (NEC)
> 0,90 mmIIAD
≥ 0,65 mmIIB3C
Special approvals upon request

Вид фланцевого соединения

 EN 1092-1, Форма B1
ASME B16.5 CL 150 R.F.
other connections upon request

Модели и спецификация

There are four different designs:

End-of-line deflagration flame arrester, basic design

BE/HK - –

End-of-line deflagration flame arrester with heating jacket


Special designs available on request

Диаграммы пропускной способности

Диаграммы пропускной способности были определены с помощью калибрированной и сертифицированной объединением технического надзора (TÜV) проточной измерительной установки. Пропускная способность V. в м³/час определена воздухом при нормальных атмосферных условиях в соответствии с ISO 6358 (20°C, 1 бар). Преобразование для различных плотностей и температур см. главу 1: Технические основы