BR/TS-80-IIB3

BR/TS-80-IIB3

Detonation Flame Arrester

for tank ships and containers

Função e descrição

The PROTEGO® BR/TS-80-IIB3 detonation flame arrester was developed for protecting tankships but can also be used for containers. These devices are especially used on tank ships operating on inland waterways or coastal shipping. The device is installed on the tank or a pipe section connected to the tank with a nominal size of 250 mm / 10" and connected to the vapour balancing line (DN 80 / 3"). The individual tanks connected via the vapour balancing line are technically decoupled by the Detonation arresters and protected.

The device protects against unidirectional detonation. In particular, the arrester consists of a shock absorber (1) and the PROTEGO® flame arrester unit (2). The PROTEGO® flame arrester unit consists of several FLAMEFILTER® discs (3) and spacers firmly held in a FLAMEFILTER® cage (4). It is moveable and can be folded to the side for maintenance. The Primary goal of this design is to enable the tank to be vented or supplied with air in an emergency when ice or crystallizing products Clog the FLAMEFILTER® . The PROTEGO® BR/TS flame arrester is available for explosion groups IIA to IIB3 (NEC group D and C MESG ≥ 0.65 mm).

The standard design is approved up to an operating temperature an operating pressure up to 1.55 bar / it meets all the conditions of the ADN* transport on European Inland Waterways.

Type-EN ISO 16852 and classification societies are available.

Características especiais e vantagens

  • meets all ADN* requirements
  • flat design
  • the emergency venting with the flexibly mounted flame arrester enables use even in bad weather conditions as well as with contaminated products
  • extraordinarily easy to service
  • the design of the PROTEGO® flame arrester unit enables individual FLAMEFILTER® discs to be replaced
  • we offer support in calculating loading and unloading rates
  • applicable for nearly all flammable liquids
  • may be used as maintenance and cleaning hatch
  • cost efficient spare parts

* European Agreement concerning the International Carriage of Dangerous Goods by Inland Waterways

BR/TS-80-IIB3

Seleção do material do corpo

Versão AB
Corpo Aço Aço inoxidável
Tampa Aço Aço inoxidável
VedaçãoTankatiteTankatite
Conjunto abafador de chamasAA
Versão AB
Corpo Aço Aço inoxidável
Tampa Aço Aço inoxidável
VedaçãoTankatiteTankatite
Conjunto abafador de chamasAA

Material selection for flame arrester unit

Versão A
Armação do jogo de FLAMEFILTER® Aço inoxidável
FLAMEFILTER® Aço inoxidável
Espaçadores Aço inoxidável
Versão A
Armação do jogo de FLAMEFILTER® Aço inoxidável
FLAMEFILTER® Aço inoxidável
Espaçadores Aço inoxidável

BR/TS-80-IIB3

Tipo de conexão flangeada

EN 1092-1; Form B1
ASME B16.5; 150 lbs RFSF
EN 1092-1; Form B1
ASME B16.5; 150 lbs RFSF

Outras conexões sob solicitação

BR/TS-80-IIB3

Diagrama de vazão

Este diagrama de vazão foi determinado em uma bancada de medição de vazão calibrada e certificada pela TÜV. A vazão V em m³/h se refere ao estado técnico padrão de ar, conforme ISO 6358 (20°C, 1bar). Para conversão em outras densidades e temperaturas, veja o cap. 1: Bases técnicas.

BR/TS-80-IIB3
BR/TS-80-IIB3