ER/V-F

ER/V-F

Pressure Relief Valve

Función y Descripción

The ER/V-F type PROTEGO® valve is a highly developed emergency pressure relief valve with high flow capacity. It is primarily used as a safety device for emergency pressure relief for storage tanks, containers, silos, and process engineering equipment; it offers reliable protection against overpressure and prevents impermissible product vapor loss close to the set pressure. It is designed to discharge particularly large amounts to prevent the vessel from rupturing in a emergency case. The spring-loading allows for higher set pressures than those with the ER-V-LP, ER/V or ER/VH.

The device will start to open as soon as the set pressure is reached and only requires 10% overpressure to full lift. Continuous investments into research and development have allowed PROTEGO® to develop a low pressure valve which has the same opening characteristic as a high pressure safety relief valve. This “full lift type” technology allows the valve to be set just 10% below the maximum allowable working pressure of the tank and still safely vent the required mass flow.

Due to the highly developed manufacturing technology, the tank pressure is maintained up to the set pressure, with a tightness that is far superior to the conventional standard. This feature is achieved by valve seats made of high-grade steel with an inserted O-ring seal, a precisely lapped valve pallet, as well as a reinforced housing design. After the excess pressure is relieved, the valve reseats and provides a tight seal again.

Características especiales y ventajas

  • “full lift type” technology valve utilizes only 10% overpressure to reach full lift
  • excellent tightness and hence least possible product losses and reduced environmental pollution
  • the set pressure is close to the opening pressure which results in best possible pressure management of the system
  • high flow capacity
  • the valve pallet is guided within the housing to protect against harsh weather conditions
  • can be used in areas subject to explosion hazards
  • reinforced housing design
  • spring-loading for high set pressures
  • best technology for API-tanks

Dimensiones

To select the nominal size (DN), use the flow capacity chart on the following page

DN200 / 8"250 / 10" 300 / 12" 350 / 14" 400 / 16" 450 / 18" 500 / 20" 600 / 24" 700 / 28"
a465 / 18.31550 / 21.65650 / 25.59650 / 25.59800 / 31.50800 / 31.501000 / 39.371000 / 39.371200 / 47.24
b860 / 33.86860 / 33.861170 / 46.061170 / 46.061150 / 45.281175 / 46.261430 / 56.301425 / 56.101690 / 66.54
(≤370 mbar)(≤240 mbar)(≤240 mbar)(≤270 mbar)(≤220 mbar)(≤170 mbar)(≤130 mbar)(≤140 mbar)(≤140 mbar)
(≤148 inchW.C.)(≤96 inchW.C.)(≤96 inchW.C.)(≤108 inchW.C.)(≤88 inchW.C.)(≤68 inchW.C.)(≤52 inchW.C.)(≤56 inchW.C.)(≤56 inchW.C.)
b980 / 38.58980 / 38.581490 / 58.661490 / 58.661490 / 58.661515 / 59.651660 / 65.351655 / 65.161910 / 75.20
(>370 mbar)(>240 mbar)(>240 mbar)(>270 mbar)(>220 mbar)(>170 mbar)(>130 mbar)(>140 mbar)(>140 mbar)
(>148 inchW.C.)(≤96 inchW.C.)(≤96 inchW.C.)(≤108 inchW.C.)(≤88 inchW.C.)(≤68 inchW.C.)(≤52 inchW.C.)(≤56 inchW.C.)(≤56 inchW.C.)
DN200 / 8"250 / 10" 300 / 12" 350 / 14" 400 / 16" 450 / 18" 500 / 20" 600 / 24" 700 / 28"
a465 / 18.31550 / 21.65650 / 25.59650 / 25.59800 / 31.50800 / 31.501000 / 39.371000 / 39.371200 / 47.24
b860 / 33.86860 / 33.861170 / 46.061170 / 46.061150 / 45.281175 / 46.261430 / 56.301425 / 56.101690 / 66.54
(≤370 mbar)(≤240 mbar)(≤240 mbar)(≤270 mbar)(≤220 mbar)(≤170 mbar)(≤130 mbar)(≤140 mbar)(≤140 mbar)
(≤148 inchW.C.)(≤96 inchW.C.)(≤96 inchW.C.)(≤108 inchW.C.)(≤88 inchW.C.)(≤68 inchW.C.)(≤52 inchW.C.)(≤56 inchW.C.)(≤56 inchW.C.)
b980 / 38.58980 / 38.581490 / 58.661490 / 58.661490 / 58.661515 / 59.651660 / 65.351655 / 65.161910 / 75.20
(>370 mbar)(>240 mbar)(>240 mbar)(>270 mbar)(>220 mbar)(>170 mbar)(>130 mbar)(>140 mbar)(>140 mbar)
(>148 inchW.C.)(≤96 inchW.C.)(≤96 inchW.C.)(≤108 inchW.C.)(≤88 inchW.C.)(≤68 inchW.C.)(≤52 inchW.C.)(≤56 inchW.C.)(≤56 inchW.C.)

Dimensiones en mm / pulgadas

ER/V-F

Selección de materiales

Design A B
HousingSteelStainless Steel
Valve seatStainless SteelStainless Steel
Valve palletStainless Steel or Steel-Stainless SteelStainless Steel
SealingFPMFPM
WeightSteelStainless Steel
Design A B
HousingSteelStainless Steel
Valve seatStainless SteelStainless Steel
Valve palletStainless Steel or Steel-Stainless SteelStainless Steel
SealingFPMFPM
WeightSteelStainless Steel

Special materials upon request

ER/V-F

Tipo de bridas de conexión

EN 1092-1; Form B1
ASME B16.5; 150 lbs RFSF
EN 1092-1; Form B1
ASME B16.5; 150 lbs RFSF

other types upon request

Modelo y especificación

The valve pallet is spring-loaded. Lower pressures are achieved with the ER-V-LP, ER/V and ER/VH designs.

Pressure valve in basic design

ER/V-F

Pressure valve in basic design

ER/V-F

Additional special devices available upon request.

Settings

>+60 mbar

+500 mbar

>+24 inch W.C.

+200 inch W.C.

Higher pressure settings, upon request. Lower pressure settings, see types ER-V-LP, ER/V and ER/VH.

ER/V-F

Diagrama de flujo volumétrico

Los diagramas de flujo volumétrico han sido determinados con un banco de pruebas de caudal calibrado y certifi - cado por TÜV. El flujo volumétrico V. en [m³/h] y el CFH se refi eren a las condiciones estándar de referencia de aire según ISO 6358 (20°C, 1bar). La conversión a otras densidades y temperaturas están referidas en el Vol. 1: “Fundamentos Técnicos”.

ER/V-F
ER/V-F