D/SVL

D/SVL

Pressure Relief Valve

Función y Descripción

The D/SVL type PROTEGO® valve is a high performance pressure relief valve. It is primarily used as a safety device for relieving pressure in tanks, containers, and process engineering equipment. The valve offers reliable protection against overpressure and prevents the unacceptable loss of product vapors close to the set pressure.

The device will start to open as soon as the set pressure is reached and only requires 10% overpressure to full lift. Continuous investments into research and development have allowed PROTEGO® to develop a low pressure valve which has the same opening characteristic as a high pressure safety relief valve. This “full lift type” technology allows the valve to be set just 10% below the maximum allowable working pressure of the tank and still safely vent the required mass flow.

Due to the highly developed manufacturing technology, the tank pressure is maintained up to the set pressure, with a tightness that is far superior to the conventional standard. This feature is achieved by valve seats made of high quality stainless steel and with precisely lapped valve pallets (1) or with an air cushion seal (2) in conjunction with high quality FEP diaphragm. The valve pallets are also available with a PTFE seal to prevent the valve pallet from sticking when sticky products are used, and they enable the use of corrosive media. After the excess pressure is discharged, the valve reseats and provides a tight seal again.

The optimized fluid dynamic design of the valve body and valve pallet is a result of many years of research work, which allow a stable operation of the valve pallet and optimized performance resulting in reduction of product losses.

Características especiales y ventajas

  • “full lift type” technology valve utilizes only 10% overpressure to reach full lift
  • extreme tightness and hence least possible product losses and reduced environmental pollution
  • the set pressure is close to the opening pressure which results in best possible pressure management of the system
  • extremely high fl ow capacity
  • the valve pallet is guided within the housing to protect against harsh weather conditions
  • can be used in areas subject to an explosion hazard

Dimensiones

To select the nominal size (DN), use the flow capacity chart on the following page

DN50 / 2" 80 / 3"100 / 4"150 / 6"200 / 8" 250 / 10"300 / 12
a336 / 13.23412 / 16.22444 / 17.48564 / 22.20664 / 26.20687 / 27.05687 / 27.05
b200 / 7.87295 / 11.61295 / 11.61465 / 18.31550 / 21.65650 / 25.59650 / 25.59
DN50 / 2" 80 / 3"100 / 4"150 / 6"200 / 8" 250 / 10"300 / 12
a336 / 13.23412 / 16.22444 / 17.48564 / 22.20664 / 26.20687 / 27.05687 / 27.05
b200 / 7.87295 / 11.61295 / 11.61465 / 18.31550 / 21.65650 / 25.59650 / 25.59

Dimensiones en mm / pulgadas

D/SVL

Detail X

Detail X

Selección de materiales para la vivienda

Design AB
HousingSteelStainless Steel
Valve seatStainless SteelStainless Steel
SealingPTFEPTFE
Weather hoodStainless SteelStainless Steel
Design AB
HousingSteelStainless Steel
Valve seatStainless SteelStainless Steel
SealingPTFEPTFE
Weather hoodStainless SteelStainless Steel

Special materials upon request

Selección de materiales para la válvula de presión

Design  ABCDEF
Pressure range [mbar]
[inch W.C.]
+2,0 up to +3,5
+0.8 up to +1.4
>+3,5 up to +14
>+1.4 up to +5.6
>+14 up to +35
>+5.6 up to +14
>+35 up to +60
>+14 up to +24
>+14 up to +35
>+5.6 up to +14
>+35 up to +60
>+14 up to +24
Valve palletAluminiumStainless SteelStainless SteelStainless SteelStainless SteelStainless Steel
SealingFEPFEPMetal to MetalMetal to MetalPTFEPTFE
Design  ABCDEF
Pressure range [mbar]
[inch W.C.]
+2,0 up to +3,5
+0.8 up to +1.4
>+3,5 up to +14
>+1.4 up to +5.6
>+14 up to +35
>+5.6 up to +14
>+35 up to +60
>+14 up to +24
>+14 up to +35
>+5.6 up to +14
>+35 up to +60
>+14 up to +24
Valve palletAluminiumStainless SteelStainless SteelStainless SteelStainless SteelStainless Steel
SealingFEPFEPMetal to MetalMetal to MetalPTFEPTFE

Special materials and devices with higher set pressure or vacuum are available upon request

D/SVL

Detail X

Detail X

Tipo de bridas de conexión

EN 1092-1; Form B1
ASME B16.5; 150 lbs RFSF
EN 1092-1; Form B1
ASME B16.5; 150 lbs RFSF

other types upon request

Modelo y especificación

The valve pallet is weight-loaded. Higher pressures can be achieved upon request with a special spring-loaded design.

Pressure valve in basic design

D/SVL -

Pressure valve in basic design

D/SVL -

Additional special devices available upon request.

Settings

Pressure:

+2.0 mbar

+60 mbar

+2.0 inch W.C.

+24 inch W.C.

Higher pressure settings upon request.

D/SVL

Detail X

Detail X

Diagrama de flujo volumétrico

Los diagramas de flujo volumétrico han sido determinados con un banco de pruebas de caudal calibrado y certifi - cado por TÜV. El flujo volumétrico V. en [m³/h] y el CFH se refi eren a las condiciones estándar de referencia de aire según ISO 6358 (20°C, 1bar). La conversión a otras densidades y temperaturas están referidas en el Vol. 1: “Fundamentos Técnicos”.

D/SVL

Detail X

Detail X

D/SVL

Detail X

Detail X