Skip to main content
 logo

FA-E-IIA1

In-Line Deflagration Flame Arrester for biogas, sewage gas and landfill gas, eccentric design, bidirectional, endurance burning proof (under atmospheric conditions up to DN 200 / 8“)

  • state of the art design for bio-, sewage- and landfill gas applications
  • eccentric design prevents condensate build up
  • offers a wide range of applications
  • special design for elevated operating pressures available
  • modular design enables each individual FLAMEFILTER® to be replaced
  • easy to maintain and the FLAMEFILTER® can be quickly removed and installed
  • eccentric design eases installation close to floors and walls
  • provides protection against deflagrations and endurance burning for explosion group IIA1- methane (former designation Expl.gr. I)
  • bidirectional operation as well as any direction of flow and installation position
  • endurance burning proof under atmospheric conditions up to DN 200 / 8” and therefore the installation of temperature sensors is not required
  • installation of temperature sensors is possible
  • cost efficient spare parts

Función y Descripción

The PROTEGO® FA-E-IIA1 series of in-line deflagration flame arresters is designed with an eccentric housing to automatically drain condensate build up in the housing. The PROTEGO® FA-E-IIA1 in-line flame arrester was specially developed for bio-, sewage- and landfill-gas applications. The application as an endurance burning proof in-line device under atmospheric conditions without extensive temperature monitoring is of advantage. Due to its eccentric design and in contrast to conventional concentric flame arresters the device can be installed in pipelines that run close to floors or walls. When installing the deflagration flame arrester make sure that the distance between potential ignition sources and the location of the installed device does not exceed the L/D ratio (pipe length/pipe diameter) for which the device was approved. According to EN ISO 16852 the installation limits are (L/D)max ≤ 50 for deflagration flame arresters for explosion group IIA1- methane (former designation Expl.gr. I).

The deflagration flame arrester is symmetric and offers bidirectional flame transmission protection. The arrester essentially consists of two housing parts (1) and the PROTEGO® flame arrester unit (2) in the center. The PROTEGO® flame arrester unit is modular and consist of several FLAMEFILTER® (3) and spacers firmly held in a FLAMEFILTER® casing. The PROTEGO® FA-E-IIA1 flame arrester protects against deflagrations and endurance burning (under atmospheric condition up to DN 200 / 8”) of explosion group IIA1 - methane (former designation Expl.gr. I). The PROTEGO® FA-E devices for substances of explosion groups IIA, IIB3 and IIC (NEC groups B, C, and D) are shown on separate pages.

The standard design can be used up to an operating temperature of +60°C / 140°F and up to an absolute operating pressure of 1.1 bar / 15.9 psi. Numerous devices with special approvals can be obtained for higher temperatures and pressures.

Type-approved according to ATEX Directive and EN ISO 16852 as well as other international standards.

Dimensiones

To select the nominal size (DN), please use the flow capacity charts on the following pages

DN25 / 1"32 / 1¼"40 / 1½"50 / 2"65 / 2½"80 / 3"100 / 4"125 / 5"150 / 6"200 / 8"250 / 10"300 / 12"
a304 / 11.97304 / 11.97310 / 12.20314 / 12.36360 / 14.17364 / 14.33370 / 14.57435 / 17.09440 / 17.32450 / 17.72480 / 18.90500 / 16.69
b29 / 1.1429 / 1.1429 / 1.1429 / 1.1438 / 1.4938 / 1.4939 / 1.5365 / 2.5665 / 2.5655 / 2.1758 / 2.2860 / 2.36
c185 / 7.28185 / 7.28210 / 8.27210 / 8.27250 / 9.84250 / 9.84275 / 10.83385 / 15.16385 / 15.16450 / 17.72500 / 19.69575 / 22.64
d400 / 15.75400 / 15.75410 / 16.14410 / 16.14440 / 16.14440 / 16.14460 / 18.11520 / 20.47520 / 20.47540 / 21.26570 / 22.44600 / 23.62
Dimensiones en mm / pulgadas

Selección de materiales para la vivienda

DesignBC
HousingSteelStainless Steel
GasketPTFEPTFE
Flame arrester unitA, BB
* for devices exposed to elevated temperatures above 150°C / 302°F (T150), gaskets made of PTFE. The housing can also be delivered in carbon steel with an ECTFE coating. Special materials upon request.

Combinación de materiales para la unidad apagallamas

Design AB
FLAMEFILTER® cageSteelStainless Steel
FLAMEFILTER®*Stainless SteelStainless Steel
SpacersStainless SteelStainless Steel
*the FLAMEFILTER® is also available in the materials Tantalum, Inconel, Copper, etc. when the listed housing and cage materials are used. Special materials upon request.

Selección del grupo de explosión

MESGExpl. Gr. (IEC / CEN)
≥ 1.14 mmIIA1 (I)*
* former designation Expl.gr. I Special approvals upon request

Selección de la máxima presión de operación

Expl.Gr.DN25 / 1"32 / 1¼"40 / 1½"50 / 2"65 / 2½"80 / 3"100 / 4"125 / 5"150 / 6"200 / 8"250 / 10"300 / 12"
IIA1 (I)Pmax1,9 / 27.51,9 / 27.51,9 / 27.51,9 / 27.51,9 / 27.51,9 / 27.51,9 / 27.51,9 / 27.51,9 / 27.51,9 / 27.51,9 / 27.51,9 / 27.5
Pmax = Maximum allowable operating pressure in bar / psi absolut, higher operating pressure upon request

Especificación de la máx. temperatura de operación

≤ 60°C / 140°FTmaximum allowable operating temperature in °C
-Designation
higher operating temperatures upon request

Tipo de bridas de conexión

EN 1092-1; Form B1
ASME B16.5 CL 150 R.F.
other connections upon request

Modelo y especificación

There are three different designs:

Basic in-line deflagration flame arrester

FA-E - –

In-line deflagration flame arrester with integrated temperature sensor* as additional protection against short-time burning from one side

FA-E - T

In-line deflagration flame arrester with two integrated temperature sensors* for additional protection against short-time burning from both sides

FA-E - TB

Additional special devices available upon request
*Resistance thermometer for device group II, category (1) 2 (GII cat. (1) 2)

Diagrama de flujo volumétrico

Los diagramas de flujo volumétrico han sido determinados con un banco de pruebas de caudal calibrado y certifi - cado por TÜV. El flujo volumétrico V. en [m³/h] y el CFH se refi eren a las condiciones estándar de referencia de aire según ISO 6358 (20°C, 1bar). La conversión a otras densidades y temperaturas están referidas en el Vol. 1: “Fundamentos Técnicos”.